1

How to limit wifi / lan users on PLDT Fibr Router (NO QOS)

Learn how you can limit wifi / lan users on PLDT Fibr Router without the need of QOS.

In this article, I included a video tutorial to demonstrate the needed steps to do this kind of feature on your laptop / desktop without the need of router QOS.

Video Tutorial

Download Arcai-Net Cut

Steps & Guide

Step (1/5): Enable telnet switch using fiberhomesuperadmin account.

PLDT Fibr Superadmin Credentials (2020): Click here

Step (2/5): Enable telnet Client on Windows

Step (3/5): Disable AP Isolation Telnet Credentials: Username: gepon or gpon Password gepon or gpon Command to be used: control port_fw_eligiblity_switch disable

Note: If you experience unkown command on Telnet you can SKIP this part and continue to STEP 4 & 5.

Step (4/5): Install Arcai Netcut on Windows or Android (Download Link Above)

Step (5/5): Configure / limit speeds of users! http://www.arcai.com/netCut/s/




PLDT Fibr Boost 2.4 Ghz Best Wifi Settings

In this video-article, I’ll be showing you how you can boost your PLDT Fibr’s 2.4 Ghz Wifi Network. Settings shown on this video tutorial may vary depending on your router however terminologies are usually similar to one another.

Steps & Instructions

  1. Download & Install Wifi Channel Scanner or you may install on your mobile phone Wifi Analyzer.
  2. Login to your PLDT Home Fibr Router using the FULL ADMIN ACCESS.
    • To learn more on how to access the FULL ADMIN ACCCESS of PLDT Fibr Router check out this video tutorial or article.
  3. Follow along the video tutorial, on how you can use the app to choose the best wifi channel for your 2.4 Ghz wifi network and change the necessary settings as shown on the video.

Video Tutorial

Required resources




PLDT: Limit Wifi Speed using Telnet on PLDT Fibr Router

This will be a step-by-step guide on how you could limit wifi speeds using the telnet method on your PLDT Fibr router.

NOTE: On the video, a lot got confused about the set part, I wasn’t hitting the enter key but rather I was pressing tab to fill up the next possible command automatically.

I made this tutorial step-by-step to clear out any confusion.

Requirements

Before we start you’ll be needing to know a few things.

You must know what kind of router are you using, this method is only tested on router model AN5506-04-FA.

Next, get the latest admin credentials on this article / guide and included on that guide is a video tutorial on how you could login to a full admin account on a PLDT Fibr router.

All set? So let’s get started!

Video Tutorial

Step by step guide

First go to your browser 192.168.1.1/fh then log in to the fiberhomesuperadmin account.

(Don’t know how or what’s the username and password? Click here)

Enable the telnet switch and web admin switch under the debug switch and hit the apply button. After that, logout.

Login now to adminpldt account check again the credentials here;

The username and passwords vary depending on your router model and version.

Upon logging in, click on the broadband settings under the network tab.

Enable all 2.4Ghz and 5Ghz binding namely SSID 1, SSID 2, SSID 3, and SSID 4 by ticking the checkbox then scroll down and hit the apply button.

By enabling these bindings you’re making sure that later when you create different wifi networks those wifi networks will have internet connection.

By default if you create other wifi networks they will have no internet that’s the fix for that one.

Next enable the telnet on your windows by going to start menu and search for apps & features.

Scroll down to the bottom and click on the Programs and Features under related Settings.

On the left pane, click the turn windows features on or off. Enable telnet client by checking the box and click on the apply button.

After than open a command prompt as administrator

  • (Windows 10) right clicking on your start menu > Command Prompt as administrator
  • (Other versions) search for command prompt > right click on it > Run as Administrator.

Type in telnet 192.168.1.1 (or your router ip address). (mine is 192.168.1.3)

For the login, type in gepon or gpon (whichever works for you) and password gepon or gpon.

Upon logging in, type in enable then the password that worked for you gepon or gpon.

Next, type in “cd pon”, if you don’t have this one or you’re redirected to gpon then this tutorial won’t work for you. Your router have no limiting functionality for wifi ssid’s.

After that, type in:

set ssid_rate_limit ssid <0-7> dir all max_rate <BW in kbps>

Terms:

  • <0-7> = 0-3 are the first four 2.4 Ghz SSID or WIFI ID’s and 4-7 are the four 5Ghz SSID or WIFI ID’s.
  • <BW in kbps> = Bandwidth speed in Kb/s for example 5 Mbps speed is 5000 kbps.
  • So to limit the first 2.4Ghz wifi with only 5 Mbps the command is:
  • set ssid_rate_limit ssid 0 dir all max_rate 5000

To remove the limit just set the max_rate to 0 and it will remove any wifi speed limit.

Example: To remove the 5 Mbps limit on the first 2.4Ghz wifi the command is “set ssid_rate_limit ssid 0 dir all max_rate 0”

After that, that’s it! Try connecting to that particular wifi and you’ll notice that it’s already limited to what you’ve set.

Enjoy and goodluck!




How to enable LAN PORTS on PLDT ONU Fibr Router

A step-by-step guide and procedure on how you could enable all LAN PORTS on your PLDT Fibr Router.

Before you could enable your router’s lan ports, you’ll need to know how you could access your PLDT Router’s FULL admin account. Yes, that’s right FULL ADMIN account is different from your default admin account provided by PLDT.

Why is that so? One main reason in separating and restricting users from accessing all the features of the router is to lessen technical support and problems encountered due to misconfigurations of settings.

It makes sense that basic home users have very-little to no technical knowledge / background when it comes to configuring techy-features that may be available on your router.

To access your full admin account, follow this tutorial before doing the steps below.

NOTE: This is only tested on AN5506-04-FA Procedure but it should work on most ONU Fibr modems.

Video Tutorial

STEPS

  • Log in with the FULL ADMIN access on your router to access these tabs and settings. Follow this link for the latest credentials for the router.
  • Click on the Network tab and broadband settings.
  • On the Internet Settings under the Broadband Settings, enable all LAN BINDING (LAN 1/2/3/4) by ticking on the checkbox.
  • After than scroll down and click the apply button. (IMPORTANT)
  • Once done, simply restart your router and check if the lan ports are working properly.

That’s it! You’ve successfully enabled all LAN PORTS on your PLDT ONU Fibr Router. Let me know if that worked for you by commenting down below.

Feel free to ask questions here or through YouTube comments / website forum / facebook page! I’ll try to help you out as much as I can.




PLDT Full Admin Access Credentials (RP2602 RP2613 RP2627 RP2646 and RP2684)

The latest as of (April 2020) full admin credentials to PLDT Home Fibr routers version RP2627, 2646 and RP2684 will be posted here along with the step-by-step instructions to assist you in accessing your PLDT router.

Video Tutorial

Credentials (RP2646 & RP2684)

FIBERHOMESUPERADMIN ACCOUNT

Router address: 192.168.1.1/fh

Username: f9!6b1e1rhO3es~u!p@e#r$a%d^m*i(n
Password: s)f_U+h|g{u@5h2o1q0b1l
FIBERHOMESUPERADMIN ACCOUNT CREDENTIALS TESTED APRIL 2020 @ AN5506-04-FA MODEL

ADMINPLDT ACCOUNT

Router address: 192.168.1.1/fh

Username: adminpldt
Possible Password/s: z6dUABtl270qRxt7a2uGTiw
6GFJdY4aAuUKJjdtSn7dC2
3UJUh2VemEfUtesEchEuSHA
1234567890
pldt1234
IF YOU HAVE CHANGED IT BEFORE TRY YOUR OLD PASSWORD
ADMINPLDT ACCOUNT CREDENTIALS TESTED APRIL 2020 @ AN5506-04-FA MODEL
ADDITIONAL NOTES:


Credentials (RP2627)

FIBERHOMESUPERADMIN ACCOUNT

Router address: 192.168.1.1/fh

Username: fiberhomesuperadmin
Password: sfuhgu
FIBERHOMESUPERADMIN ACCOUNT CREDENTIALS TESTED FOR RP2627 FIRMWARE

ADMINPLDT ACCOUNT

Router address: 192.168.1.1/fh

Username: adminpldt
Possible Password/s: 6GFJdY4aAuUKJjdtSn7dC2x
ADMINPLDT ACCOUNT CREDENTIALS TESTED APRIL 2020


Credentials (RP2613)

FIBERHOMESUPERADMIN ACCOUNT

Router address: 192.168.1.1/fh

Username: admin1234
Password: admin1234
FIBERHOMESUPERADMIN ACCOUNT CREDENTIALS FOR RP2613 FIRMWARE

ADMINPLDT ACCOUNT

Router address: 192.168.1.1/fh

Username: adminpldt
Password: 6GFJdY4aAuUKJjdtSn7dC2x
ADMINPLDT ACCOUNT CREDENTIALS FOR RP2613 FIRMWARE


Credentials (RP2602) (Tested on HG6245D)

FIBERHOMESUPERADMIN ACCOUNT

Router address: 192.168.1.1/fh

Username: f~i!b@e#r$h%o^m*esuperadmin
Password: s(f)u_h+g|u
FIBERHOMESUPERADMIN ACCOUNT CREDENTIALS FOR RP2602 FIRMWARE

ADMINPLDT ACCOUNT

Router address: 192.168.1.1/fh

Username: adminpldt
Password: z6dUABtl270qRxt7a2uGTiw
ADMINPLDT ACCOUNT CREDENTIALS FOR RP2602 FIRMWARE


Instructions

  1. Open a web browser, type in the address bar 192.168.1.1/fh
  2. Enter the FIBERHOMESUPERADMIN credentials (see table above) then log in.
  3. Click on the debug switch upon login and look for Web-Admin Switch toggle to enable then hit the apply button.
  4. Logout from the FIBERHOMESUPERADMIN account.
  5. Type once again on the URL 192.168.1.1/fh
  6. Enter the ADMINPLDT credentials (see table above) then log in.
    • NOTES:
    • If you get an error of invalid password/credentials make sure you are copying without any space from the table above.
      • Check if your software version is the same with the credentials you’re copying.
      • For HG6245D, check the RP2602 credentials above. If the adminpldt doesn’t work try resetting your modem by pressing on the small pinhole beside the WPS button on your router then try again.
    • If you see “Someone is already logged in“, simply restart your modem.
    • If you have a different version or router other than mentioned above it is not guaranteed to work. Feel free to ask on the forums on this website or comment below (signup / login using Facebook or Google account).

This may or may not work for you since PLDT changes the credentials once in a while so if this worked for you leave a comment below or if you have discovered a new credentials that worked for you feel free to share it to FST Community by commenting below, or posting a thread in the forum or through YouTube comments or Facebook.